homeinfotuningstylinggallerymessage boardlinks

STYLING PRODUCTS - a few manufacturers have started to realise that there's a market for producing trick styling products for auto scooters - here's a selection of styling ideas to whet your appetite:

Steel footplates - Stoffi's Garage in Austria are the supplier of these fine steel footplates. The original plastic surface underneath can then be protected from wear and scratches.
Possibly the coolest looking footplates are these available from PM Tuning. They're made out of aluminium and a feature a cool laser cut design. They're lightweight too in comparison to other footplates on the market.
Footpegs - These CNC machined footpegs from OEM (Oberon Engineering) are made from billet aluminium, colour anodised and use stainless steel fasteners as grip studs for your boots. You won't find a better looking replacement footpeg anywhere.
Brake levers - Enhance your handlebars with a pair of anodised or carbon-effect brake levers available from JASScooters and also Chiselspeed.
Pilion seat cover - replace your passenger seat with a body-coloured cover like this one. 50cc Dragsters don't have a pillion seat so the rear-end of the bike really benefits visually. Available from Stoffi's Garage or try your Italjet dealer.
Carbon fibre - PM Tuning's rear hugger, front mudguard and air scoop really enhance the look of the Dragster and have the added advantage of being significantly stronger and lighter. A carbon flywheel cover is also available.
Carbon air scoop - Available from PM Tuning and now JASScooters (pictured here) is this carbon air scoop for your transmission cover, not only does the scoop look trick it acts as an air feed to your clutch to assist in cooling.
Carbon windshield - Manufactured by Rage Composites and available from JASScooters is this carbon windshield. Not only will it give you a bit of wind protection it looks good too and has a quality finish.
Revised number plate bracket - Stoffi's Garage can supply you with this revised number plate bracket, the existing light fitting is then bolted on to it. This new configuration enhances the rear profile of the Dragster.
Brake light lens - replace the standard lens with a clear or carbon-look one off a Yamaha Aerox (same fitting as the Dragster). Available from Tunescoot in Germany.
Number plate light - this light (approximately 2cm high) is available from SIP Scootershop in Germany, two of them look even better mounted at the rear of your Dragster and will light up your number plate adequately.
Handlebar grips - ACSUD do a range of grips which will fit the Dragster. There's a certain technique to fitting these, use plenty of heat and soapy water for the grips to expand sufficiently before they start to contract once they're on the bike.
Liven up your handlebars with Areite's "Harri's" range of grips. They're made out of transparent plastic and various inserts featuring funky graphics are available.
Brake braiding - JASScooters brake switch cable sleeve in stainless steel braid with chrome plated aero fitting gives enhanced looks. The original stainless steel spring can be put over the top to look really cool.
Coolant hose - stainless steel over braiding to give a cool look to your water pipes, complete with anodised fittings. This kit available from JASScooters.
Dials & guages - in this novel example we see the addition of an Italjet Formula fuel and temperature guage adorning what would otherwise have been the mobile phone compartment. Functionality and a clever use of space in the process.
Paint - transform the look of your bike with a lick of paint, the standard air-filter casing for example will look significantly better given a glossy coat as opposed to the dull matt finish of the original grey plastic.
'Bum-Stop' seat pad - enhance looks and improve both passenger safety and comfort with this seat pad from PSN Scooters.
Seat upholstery - treat the standard seat as a clean canvas for applying your own design, get your seat re-upholstered in leather. The results can be visually striking.
Grille mesh - replace all those fake vents with some aluminium grille mesh. Companies such as Larkspeed and Demon Tweeks are worth checking out.
Tax disc holders - the simplest of accessories, there are several available now. Why not go that bit further and get yours re-sprayed to colour-code with your bike?
Bolts & fasteners - the final touch really, finish off those wheel bolts with some anodised cup washers and button caps. These are from the Hyperbolt range. Pro-Bolt also do a range of trick glow-in-dark bolts aptly named, you guessed it, 'Glo-Bolt'.